PADS is one of Mentor Graphics’s most popular products, specially developed for the design and manufacture of electrical circuits (PCBs). The software is actually a lightweight, easy-to-use Xpedition Enterprise software application that works for beginners and small and not very complex designers. The PADS-winning sheet of the Xpedition Enterprise is actually its higher speed and less costly; working with PADS is very easy and very suitable for small and fast designs. Electronic engineers can use this software to design and validate their electrical circuits.
PADS software , despite its simplicity and low cost, should not be underestimated as it has a lot of powerful features. This software has many simulation, analysis, and design features of advanced layouts and has a very high compatibility with other Mentor Graphics products like HyperLynx and Xpedition Enterprise.
If the software is installed on the system, each project can be imported into another software application and apply the other necessary measures on the project; the Signal Integrity and Thermal Simulation capabilities are among these capabilities.
Features of Mentor Graphics PADS:
- Simple and simple design of electrical circuits
- Designed, tested and tested circuit design
- Schematic design, layout and selective piece-to-piece
- Powerful search and filtering of various components
- Design customized templates tailored to IPC
- Compatibility and high-level coordination with HyperLynx and Xpedition Enterprise
Minimum System Requirement of Mentor Graphics PADS
- Hardware platform: PC
- Operating systems: Windows 10 (32-bit and 64-bit), Windows 7 SP1 (32-bit and 64-bit), Windows XP SP3 (32-bit)
- Memory requirements: 2GB RAM (min )
- Disk space requirements: Download 3 GB, Installation 6GB
How to Install Step by Step (Installation Guide)
Main installation and activation guide:
- First download the software and unzip it.
- Start the installation process by running the Setup.exe file (as Run as Administrator).
- If you are using a Hardware Key or a Dongle, at this point, connect it to your system and click Next.
- On the next screen you will see the No current license detected message, on this page, click Skip.
- On the next page, click Agree.
- On the next page, click Modify and enter the Product Selection tab.
- In this tab, check each module you need and finally select Done.
- Now installing the installer will start by installing it.
- After installing the program, click on at a later time, then click Done.
- Enter the Keygen folder and open the run.bat file with Notepad software.
- Regardless of changing the installation path, just replace the following:MentorKG.exe -patch C: \ MentorGraphics \ PADSVX.2.2
- Save the run.bat file and run Administrator.
- Keygen starts scanning the installed projects and modules, and after a while a Notepad page opens to you under the title LICENSE.TXT.
- In Drive C, create a folder called flexlm.
- Save the LICENSE.TXT file and save as licens.dat at C: \ flexlm. (Do not forget to put Save as type on All Files.)
- If all the steps are right, there should be no problem, and now the program is fully functional and can be used without any restrictions.
Note: If you need to install PADS Logic and PADS Docs, the installation process is exactly the same as the PADS installation process, as described above.
Activation of this software has a lot of troubles and requires a modest technical knowledge.
- The generated license is based solely on the hardware NIC (network card) and is completely different for each system.
- Unfortunately Keygen is not compatible with all network cards. During the testing phase, the software was downloaded by PC, for example, in a system with the Realtek software network card, but did not answer the Intel Pro 100/1000 MT card. .
- To find out if the program is activated, run one of the installed programs, such as PADS Layout VX.2.2, and if you get the No Licenses found message, then the License program has an issue and may not be compatible with your network card.
- If you use other Mentor Graphics products or, in general, software that is activated by the FLEXlm Network or MGLS Licensing network, you will definitely have trouble; if you can remove other software before installing this software and Or, in the steps below, check that your license is properly addressed.
- If you have also installed the PADS Logic software, you should also create a License file for it, by reading the following section carefully.
Important note about using Mentor Graphics at the same time:
- If you are using multiple Mentor Graphics products simultaneously (such as PADS and PADS Logic, or PADS, and Xpedition Enterprise) and intend to activate all of them, note that you only have a license.dat file as a License File You can give it a program and if you do not give Keygen the correct path when making the license file, activation of other programs will be lost. To be able to license for all Mentor Graphics products, you must edit the run.bat file and the address Provide the main folder where all the applications are installed, assuming that all software is in the default path itself. You must edit the run.bat file as follows:MentorKG.exe -patch C: \ MentorGraphicsIn this case, Keygen will license for all installed software and will provide you with a license.dat file that includes the activation of all company software and this file should be addressed according to the methods described in the software.
- This software has been completely tested and tested by the download team, but due to the current limitations of Keygen, it can not be activated on all systems because the software activation system is based on the MAC address and the card The network is hardware. This application may not work on your system.
- Preferably use Windows 7.
- All files can be repaired by WinRAR software and compressed as much as possible.
- The PADS software is provided only in 32-bit mode, but it is fully compatible with 64-bit systems. For information about supported windows, be sure to read the “System Requirements” section.
- Download Mentor Graphics PADS VX.2.2 x86 (32-bit version) | Size: [3379 MB]
- Download Mentor Graphics PADS Logic VX.2.2 x86 (32-bit version) | Size: [526 MB]
- Download Mentor Graphics PADS Docs VX.2.2 x86 (32-bit version) | Size: [902 MB]
- Download Crack Only | Size: [533.23 KB]
Must Have Software, Download it Now for Free & Full Version:
- Download Internet Download Manager v6.30 Build 3 Full Version
- Download Google Chrome v63.0.3239.108 Stable + Chromium v65.0.3288.0 x86 / x64
- Download Mozilla Firefox v57.0.3 x86 / x64
- Download WinRAR v5.50 x86 / x64
- Download FlashGet v1.96 + 18.104.22.1680
- Download Telegram v1.2.1 for Windows
- Download WhatsApp v0.2.7305 for Windows x86 / x64
- Download LINE v22.214.171.1245 for Windows
- Download Skype v126.96.36.199
- Download Adobe Flash Player v188.8.131.52 x86 / x64
- Download KMPlayer v184.108.40.206
- Download Microsoft Security Essentials v220.127.116.11 x86 / x64 + v4.4.304 x86
- Download ESET NOD32 Antivirus + Internet Security v18.104.22.168 x86 / x64
- Download Adobe Photoshop CC 2018 v19.0.1 x86 / x64
- Download Windows 10 Enterprise v1709 (Updated Nov. 2017) Redstone 3 x86 / x64
- Download Windows 8.1 Enterprise with Update 3 x86 / x64 RTM
- Download Windows 7 Enterprise SP1 x86 / x64 Integrated Latest Updates
- Download Microsoft Windows XP Pro SP3 x86 Integrated All Updates
- Download Microsoft Office 2016 Professional Plus Integrated October 2017 x86 / x64
- Download Microsoft Office 2013 SP1 Professional Plus Integrated August 2017 x86 / x64
- Download Microsoft Office 2010 SP2 Professional Plus Integrated August 2017 x86 / x64
- Download Recover My Files v22.214.171.1244
- Download Adobe Acrobat XI Professional v11.0.23
- Download Mozilla Thunderbird v52.5.2
- AnyDesk Free v3.6.3